How To Remove And Install An Over The Range Microwave

Download Article

Download Article

An over-the-range microwave oven makes efficient utilize of space in your kitchen, while too incorporating lighting and ventilation. After you brand sure you lot have the supplies y'all need for installation, double-check that your microwave will fit properly to a higher place your range. Mountain the microwave in place using a template and bracket, and a few simple tools.

1. 1

   Turn off the power. Since a microwave is an electrical appliance, you volition need to take intendance to avoid electrocution or other damage. Earlier y'all start installation, go to your circuit breaker, and flip the breaker for the range to the "off" position.^[ane]

2. 2

   Make sure at that place'south an outlet nearby. Most over the range microwaves include a short power cord that is designed to feed upwards into the chiffonier that the appliance will sit underneath. Ideally, there will be an electric outlet within this cabinet that you lot tin plug the ability string into.^[2]

   • Your microwave'south installation instructions volition specify whether there are acceptable alternative locations for the electrical outlet.
   • If there is not an outlet in a convenient location, contact an electrician for assistance installing one before you put the microwave in place.

   Advertisement

3. 3

   Check to make sure your microwave can be installed at the proper pinnacle. ^[3] In general the lesser of the microwave should exist no higher than 54 inches (140 cm) from the floor. In addition, in that location should be approximately twenty inches (51 cm) to 24 inches (61 cm) betwixt the bottom of the microwave and the top of the range. This will allow y'all to utilize both the microwave and the range safely and comfortably.^[4]

   • Use a record measure out to verify the top of your microwave.
   • Measure out from the bottom of the chiffonier you volition install the microwave below to the height of the microwave. Make a marking at this spot.
   • Mensurate the distance between this marker and the flooring, and the top of your range, to make sure that the microwave will be situated within the acceptable superlative range.

4. 4

   Determine the ventilation direction. The microwave itself will accept a fan, and since it sits above the range (where a range hood would ordinarily go), both appliances will have to ventilate exterior together. Ordinarily, there are two options: either the appliances will ventilate horizontally through a tube in the wall, or vertically, first through the cabinet above the microwave and so the ceiling or college upward on the wall.^[5]

   • Your microwave may have boosted fittings which you lot should set in identify in society to permit it to ventilate properly. Bank check the installation instructions that come with your particular model to exist sure.
   • If you lot do not already have a ventilation system in place, contact a contractor to have one installed.^[vi]

5. five

   Reframe the opening, if necessary. If your kitchen cabinetry and framing are sturdy, they may exist sufficient to support a relatively heavy over the range microwave. If the materials are less robust, reframe the area where you will install the microwave with 2 by fours. Some experts recommend reframing in all cases.^[vii]

   • Your microwave should come with a kit that has a framing template. Place it where y'all want the microwave to sit, and follow the guidelines to cut through the drywall.
   • Remove the drywall and pull out the insulation from the area inside the wall.
   • Secure two by fours between the wall studs. Check the instructions provided with your microwave for the verbal dimensions.
   • Fill in any empty space with new insulation.

   Advertisement

1. 1

   See if your microwave has an installation template or wall plate. Your model should come with a template to assist guide you when installing mounting hardware. Place this on the wall, and the template should tell you where to place the hardware. Some models besides come with a mounting bracket that will have pre-drilled holes then you can easily screw it in place.^[viii]

   • Use a level to brand sure that the template is square and that the microwave will sit properly in place.^[nine]

2. 2

   Find at least one stud. If yous didn't reframe the installation site, you'll need to attach the mounting hardware to at least 1 stud in the wall. Use an electronic stud finder, or gently tap on the wall with a hammer. When the taps sound dull instead of hollow, you take located a stud. Marker the site on the wall.^[10]

   • Studs are usually 16 inches (41 cm) inches apart on the wall. Once you find ane, measure out 16 inches to the either side to marking others.
   • Using your template, make sure that the hardware will be mounted on at least one of the studs. If not, reframe the site or contact a contractor for help.

3. iii

   Drill holes in the template or attach the wall plate. ^[11] Usually, over the range microwaves will be installed using toggle bolts. Predrilling holes for these bolts will make installation easier--simply follow the guidelines on your template. If you lot are using a wall plate, go ahead and install that using the hardware and guidelines given in your model's instructions.^[12]

   • About probable, y'all will demand a couple of drill $.25: smaller ones for the toggle bolts, and a larger one to make a hole to feed the microwave's power cord through the chiffonier above the appliance (if there isn't already one). Check your model's instructions, and always use the recommended tools.

4. iv

   Fix the microwave into position or onto the wall plate. It will help to take another person to help you hold up the microwave.^[13] Push it up and bring it upwards to the bottom of the chiffonier. If your model has a wall plate, fit it into the bracket that will assist hold it in place. Brand sure that someone keeps holding the microwave in place for now.^[14]

5. 5

   Plug in the microwave. Feed the microwave'due south power string through the hole drilled in the bottom of the cabinet in a higher place the apparatus. Plug the cord into the outlet within the cabinet, but don't plough the ability dorsum on yet.^[15]

6. 6

   Thread bolts through the lesser of the cabinet. Feed the bolts (or screws) supplied with your microwave (or recommended by its instructions) into the holes you previously drilled in the bottom of the chiffonier. They should slip into slots in the elevation of the microwave. Tighten them using a wrench (or screwdriver) until the microwave is securely held in identify.^[16]

   • Carefully let go of the microwave at this bespeak to make sure that it stays in place.

7. 7

   Connect the blower. Slide the exhaust fan supplied with your microwave into place at the ventilation site. Specifications will vary from model to model, so read the instructions provided with yours. Most manufacturers also recommend using an canonical sealant around the edges of the fan'due south housing to make the connection impervious.^[17]

   • You may demand to have the fan out and change its direction, depending on the orientation of your ventilation system.

8. 8

   Test the microwave. At this bespeak, you tin finally flip the excursion for the range back to the "on" position. Verify that your microwave is getting power, and test it by heating something to make sure that the apparatus is working properly.

   • If your apparatus does not seem to work properly, read the troubleshooting department of the manual, if it has one, or contact the manufacturer.

   Advert

Add together New Question

• Question

  Tin I install an over-the-range microwave by myself?

  

  Gevorg Grigorian is an Apparatus Repair Specialist and the Possessor of G and R Appliance Repair in Los Angeles, California. With over 12 years of experience, Gevorg specializes in residential and commercial appliance repairs every bit well as heating, ventilation, and ac (HVAC) services. Gevorg holds a BS in Business concern Administration and Management from California Land Academy-Northridge.

  

  Apparatus Repair Proficient

  Expert Respond

Ask a Question

200 characters left

Include your email address to go a message when this question is answered.

Submit

Ad

Video

Things You'll Need

• A drill and fix of drill bits
• A stud finder or light hammer
• A screwdriver
• An adjustable wrench
• Toggle bolts
• A level
• A tape measure
• A drywall saw
• Sealant

Almost This Article

Commodity Summary 10

Before yous install an over-the-range microwave, make certain it will be xx to 24 inches to a higher place the stovetop then they are both like shooting fish in a barrel to utilize. Then, apply the microwave'southward installation template to mark where the mounting hardware should get. Adjacent, adhere the mounting hardware to at least ane stud, which you tin can find using an electric stud finder, and lift the microwave onto it. Ship bolts through the chiffonier above the microwave and skid them into the slots on peak of the microwave to secure it. To larn how to install the ventilation system, proceed reading!

Did this summary assist yous?

Thanks to all authors for creating a page that has been read 369,970 times.

Did this commodity help y'all?

Source: https://www.wikihow.com/Install-an-Over-The-Range-Microwave

Posted by: lewisyedis1951.blogspot.com

Share this post